AirDrain For Synthetic Grass Drainage and Shockpad

1.30 – 2.00 per square foot

PRICING IS PER SQUARE FOOT NOT PER GRID SHEET – Select your quantity based on the number of square feet of coverage you need, NOT the number of grid sheets.

A grid sheet is 7 square feet of coverage, therefore you must order a minimum of 7 square feet.

We recommend adding 3 – 5 % for shrinkage when selecting your quantity.

If you are ordering 1k sqft or more call me directly @ Michael Bean 405-361-2887      

The ultimate drainage grid!

Category: Tags: , , , , , , , , , ,

Quantity based pricing table

MinMaxUnit Price
799$2.00
100249$1.80
250499$1.60
500799$1.40
8001500$1.30

Description

Top Features of the AirDrain Drainage Layer and Shockpad 

  • AirDrain can be reused when the Synthetic Turf must be replaced
  • Water harvesting reclamation and reuse is easily achieved with an AirDrain System
  • Can help qualify for LEED and other green building credits
  • ASTM testing proves AirDrain’s shock absorption properties reduce Shock Attenuation up to 20%
  • AirDrain creates and helps maintain a constant Shock Attenuation for Synthetic Turf of up to a 20% reduction.
  • There is no hindrance to drainage with AirDrain

Use Types:
Rooftops, Balconies, Synthetic Grass Turf Drainage, Dog Training Turf Areas, K9 Dog Runs, Playgrounds, and many many other uses !

Shipping:
Ships on pallets or boxed dependent on size.
This Product Ships UPS Ground and/or Freight.

Whether installed on an aggregate sub-base, concrete, asphalt or rooftop the AirDrain for Synthetic Turf drainage helps provide you with consistent drainage. AirDrain is 1 inch high, has a 92 % air void and a vertical and lateral drainage rate which cannot be matched by any other product in the industry.

AirDrain has been used in specs and projects where the city or county has limited the water that can be introduced into the sewer system or has limited the size or volume of the exit drains on a roof top.

In a Cost Value Performance scenario, no product comes close to AirDrain.

Over the years, many architects and engineers have asked us just how fast the AirDrain grid will drain. Our reply has always been that the AirDrain is only limited by what is above it and the exit drains due to the fact that the area of an AirDrain part is 1 inch high and has a 92 percent air void.

Recently, our AirDrain grid was tested using the ASTM D 4716 Hydraulic Transmissivity Standard Test Method. The testing was done using plates on top and bottom of the AirDrain part, setting them to the required slope and adding water from one end down the slope.

AirDrain was draining so fast they had to modify their testing equipment to accommodate the volume of water AirDrain could move.

As it turns out there is practically no resistance to drainage using this tile. The most important factor to consider is the percentage of slope that the AirDrain is sitting on.

To put this in perspective of rainfall, AirDrain can handle anything that Mother Nature throws at it. On a nearly completely flat surface (1/2% of 1% slope) AirDrain  will drain 2.85 inches of rainfall in one minute.

For example, it could rain over 171 inches in an hour and AirDrain could handle it.

AirDrain ‘s capability to hold water .576 gallons of water per sq ft. in the grid until the exit drains can evacuate it is another plus for the AirDrain System.

No other product on the market matches the AirDrain ability to drain a project, it’s not even close. Period ! 

This tile can also provides consistent shock attenuation properties which are a major contributor to the reduction of concussions for the safety of your players.

So when you see the claims of manufacturers rainfall per hour drainage, ask them if they have the ASTM test that really shows a products drainage capability.

 

*When installing over a rubber roofing membrane, lay down a thick geo-textile layer first. You must protect the water proofing at all costs!

* AirDrain can be made to the following specification Flammability UL 94, Flame Retardant, High Impact Polypropylene